![]() ![]() ![]() Attribute visibility can also be set when doing this. If it is a standard practice in your company to show terminals this way, then I would suggest editing the blocks themselves to show the attributes where you wish them be. You should now be able to see the information on your screen, but you many need to adjust the attribute layout and sizes. Scroll through the list and find the X?TERMDESC# attributes and click on them once so that a star appears next to them. Now you need to right click on the terminal, select the attributes sub menu, then the List/Edit command. X8 is for wires connecting from the bottom. X4 is for wires connecting from the left. X1 is for wires connecting from the right. fill in the appropriate values in the correct fields. The fields you are looking for here are the X?TERMDESC# ones. Before you click OK or OK-Repeat, click on the Show/Edit Miscellaneous button. Insert the terminal as normal and fill in the data in the dialog box. There is a way to show the information you want while only using one terminal. It leaves an empty terminal behind.įor cleanup remove the extra spare terminals that are generated (they are leftover empty terminals) and add in any hardware you need llike endplates, anchors, etc. It should pull 3.2 into the 3.1 terminal. (note: this picture was done AFTER they were assoicated (thats why 1 & 2 are already together) (see picture 3 for the "Before" image)Īfter that the Assoicate Terminal Dialog box appears, at the side browser (where it says Terminals) select 3.1 and go to level 2. Ok, First thing you can edit the Block Properties when you insert the schematic terminal or you can edit it after the fact in the terminal strip editor.Įither way you need to add 2 levels to one of the terminals ( Add it to 3.1).Īfter that you select the two terminals ( 3.1 and 3.2), make sure you select one level from 3.1 and then select the terminal on 3.2) select assoicate terminal. What would be a more standard way of showing this information? Again, this provides the info I want but I'm not documenting things in a way that allows ACADE to do more things automatically for me to save me time. Is there a more standard way of showing this information? I manually labeled the wire between blocks 5 & 6 with a JUMPER description so automatic wire numbering would just skip this wire. So Wire 228 feeds TB02:5.2 and TB02:6.2 (using my naming convention) and these blocks have direct connection to CBL20.4 (for 5.2) and CBL21.4 (for 6.2). Block 5 and 6 are jumpered together (as you can see in the WAGO layout above). In this case, Wire 228 coming from T1:X2 connects to strip TB02 at block 5.1. Is that possible?ģ) Is there a standard method within TSE to document the physical connection point information for each terminal block? If this is done, is there some way to show that physical connection info on the schematic via some type of terminal block symbol (or attribute info already present on the block)?Ĥ) I know jumper information can be supplied in TSE but how do you show jumper info on the schematic automatically? Again, trying to show the bulk of the info on the schematic to make panel building as easy as possible. First, ACADE doesn't know about my naming convention, so it thinks 3.1 and 3.2 are 2 separate terminal blocks.ġ) Is there a better (more standard) way to represent the terminal block connection information that I want on the schematic that won't cause ACADE problems and that will save me time?Ģ) I'm just learning TSE, so maybe there's a way within TSE to combine 3.1 & 3.2 into a single block. ![]() This provides all the information needed for the panel builder directly on the schematic.ĭiagrammatically this seems to work fine but when I try to generate the terminal strip layout, I have some problems. So this says that wire 219 goes from connection 2 on F5 to terminal strip TB02 : terminal block 3 (wiring position 1 ) and comes out on terminal block 3 (wiring position 2 ) which has a connection to CBL20 conductor 3. So, on a schmatic I'd lke to see something like this: Sometimes we use triple or quad blocks and the numbering works the same (1-3, 1-4, from top-bottom (right-left)). So, for block 1, the top connection is referenced as 1.1 and the bottom connection as 1.2. We reference the physical wire connection points starting at 1 at the top of block (at the right if mounted horizontally). We use primarily single level WAGO terminal blocks like this: As I stated, I'm new to ACADE 2014 and very new to Terminal Strip Editor (TSE). ![]() I'd like to be able to show the physical connection points to terminal blocks directly on my schematic. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |